White pail labelled 3-in-1 water-based floor coating
Floor Coatings
Water-Based 3-in-1 Epoxy Floor Coating
Refresh a prepared concrete or cement floor with a smooth, glossy colour finish. The water-based coating is supplied ready to apply by brush or roller. Use two coats of the same product for the standard system on a suitable base.
Where to use the coating
The 3-in-1 system combines the functions of a primer, colour coat and clear finish in the same coating. On suitable prepared floors, the supplier illustrates two coats of the same product without a separate primer or clear coat. Test adhesion first if the base is porous, polished or previously coated. Consider this coating for sound concrete and cement floors in garages, workshops, storage areas and commercial interiors. Match the system to actual traffic, cleaning, moisture and exposure. Confirm suitability for outdoor, wet, sport or other specified floors before ordering.
Product specifications
- Reference model
- JT0001.
- Material
- Ready-to-use water-based epoxy floor coating.
- Appearance
- Smooth gloss finish in solid colours.
- Application
- Brush or roller. Two coats in the standard system.
- Substrate
- Prepared concrete or cement. Assess existing finishes before coating.
- Pack sizes
- 1, 2, 5, 10, 20, 25 and 50 kg.
Prepare and apply two coats
- 01
Prepare the floor
Remove dust, grease, loose coatings and contamination. Repair surface defects, assess moisture and confirm the base is sound, clean and dry.
- 02
Check a test area
Use a small representative area to verify adhesion and appearance. Confirm any preparation or priming required for porous, polished or previously coated floors.
- 03
Brush or roll the first coat
Apply the coating as supplied, without thinning. Work in even passes and use a brush at edges where needed.
- 04
Apply the second coat and protect the floor
Wait for the first coat to reach the recommended recoat condition. Apply the second coat evenly. Keep traffic and cleaning off the area until the floor is ready for its intended use.
Confirm the recoat interval and time to service for the supplied material and actual site conditions. Temperature, humidity and airflow affect drying.
Estimate material for both coats
Estimate material for both coats. Send the floor area, substrate and condition, including any existing coating. Confirm the consumption per coat on a test area before ordering. Porous or rough floors can increase the amount required.
Choose a solid colour
Compare the solid colour references below. Room lighting, screen settings and the substrate can change the appearance. Request a physical colour sample and confirm availability before ordering. Use material from the same batch for continuous areas where possible.
Colour and application gallery
Test results for the submitted sample
Supplier-commissioned report HGW20232164, dated 29 August 2023, records the following results for the submitted 3-in-1 water-based floor coating sample under GB/T 22374-2018. Use the report conditions when comparing results. Confirm the current documentation and requirements for your project.
- Drying in the lab
- Surface dry in 0.5 h and through dry in 3 h. Site recoat and traffic times depend on actual conditions.
- Pencil scratch hardness
- B, reported as the measured result.
- Abrasion
- 0.015 g mass loss at 750 g load and 500 cycles.
- Impact
- Passed the specified 1,000 g steel-ball test.
- Water resistance
- Passed the specified 168 h test.
- Chemical exposure
- Passed the specified 72 h tests with No. 120 petroleum solvent and 20% sodium hydroxide. Confirm other exposure conditions separately.
Application questions
Does the standard system need a separate primer or clear coat?
The supplied two-coat system uses the same coating on a suitable prepared base. An adhesion test helps determine whether the actual floor needs additional preparation or a compatible primer.
Can I apply it over existing paint?
Check that the old finish is sound and compatible. Remove loose areas and contaminants, then test adhesion on a small area before coating the full floor.
How much material should I order?
Provide the area, substrate and its condition. Measure coverage for one coat on a representative test area, then estimate both coats and allow for surface profile and application losses.
Can I specify it for forklift traffic or an ESD floor?
Provide wheel loads, traffic frequency, cleaning and any required electrical resistance or other performance criteria. Agree the applicable test evidence and system before specifying the coating.
Packaging and samples
Pack references are 1, 2, 5, 10, 20, 25 and 50 kg. Confirm the selected shade, net pack weight and current packaging. Samples are free, with freight paid by the customer. Ask sales about quantity, OEM packaging and lead time.
Discuss your floor or request a sample
Send the floor area, base condition, selected colour, expected traffic and delivery country. Include photos or any project test requirements.
- sales@leadercoat.com
- Phone & WhatsApp
- +86 151 7525 6533
- Sample support
- Free samples. Customer-paid freight.